ID TECH Omni Manual de usuario Pagina 10
- Pagina / 64
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6
Codes must be typed from an external keyboard when the reader is connected to a
Notebook PC. (The Omni’s USB keyboard interface model is the best choice for use
with a Notebook PC.)
If a code is typed correctly, but the reader won’t give the appropriate beeps, it may be
necessary to press the CAPS LOCK key a few times and leave the CAPS LOCK feature
on. Then try to re-enter the confi guration code.
Default Settings
The Omni reader is shipped from the factory with the default settings already
programmed. In the following sections, the default settings are shown in
boldface
. For a list of all default settings, please see Appendix A. In order to
modify these settings, the host computer and keyboard must be IBM PC/AT-
compatible.
By default, the reader has been programmed with the least restricted settings,
thus making the Omni reader able to read most bar code labels and standard
format magnetic stripe cards out of box.
The reader’s output data format can be reconfi gured to meet the expectations
of the host application.
To reset the reader to the factory default, follow these steps:
1. On an AT-compatible computer, enter any document editor. (Notepad is
recommend in the Windows environment.)
2. Turn on the CAPS LOCK feature on the keyboard, as the confi guration
code is case sensitive.
3. Enter the GROUP SETUP MODE by typing
/E/D/FA
.
4. Press the
<Enter>
key. The reader will beep twice.
5. Type
AW
.
6. Press the
<Enter>
key. The reader will beep twice.
7. Type
AZ
.
8. Press the
<Enter>
key. The reader will sound four beeps.
Terminal Type Selection (Group A)
The Omni reader is set at the factory to interface as a PC/AT Keyboard
Wedge. To change this setting to permit the Omni to operate without an exter-
nal keyboard (as with a touch screen or laptop computer), please follow these
steps:
01 for PC/AT Keyboard Wedge
42 for PC boot-up without external keyboard
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Relacionado con productos y manuales para Lectores De Tarjetas Magnéticas ID TECH Omni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 2.546 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales