ID TECH Omni Manual de usuario Pagina 33
- Pagina / 64
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
29
SELETION CODE: H2
Send Start/Stop Sentinels A
Do Not Send Start/Stop Sentinels B
Track Two Send Accout Number Only
Track Two of a magnetically encoded credit card includes the account number
information as well as other information. If this option is selected, all other
data contained on the track is suppressed before transmission.
SELECTION CODE: H3
Track 2 Send Account Number Only A
Track 2 Not Limited to Account Number B
Track Separator
One character from the Full ASCII Table: This option allows the user to select
the character used to separate data decoded from each track when using mul-
tiple track magnetic stripe readers.
H4<ENTER><SELECTED CHARACTER><ENTER>
Note: For no track separator, enter N. Default is <ENTER>.
Reviewing Configuration Settings
The reader’s current settings can be reviewed by following these steps:
1. Locate the group that contains the settings you want to review.
2. On an AT-compatible computer, enter any document editor. (Notepad is
recommend in the Windows environment.)
3. Enter the setup mode for that group by typing
/E/D/FX
<Enter>. (X in this
case is the single alpha character identifi ed with the group located in Step 1.)
4. The reader will respond with two beeps after <ENTER> is depressed.
5. Review the settings for the group by typing
XY
<ENTER>. (X is the same
single alpha character as typed in Step 3.)
6. After <ENTER> is depressed, the reader will display the current settings
for the group onto the screen for user to review, followed by two beeps from
the reader.
7. Exit the setup mode after reviewing the settings by typing
XZ
<ENTER>.
(X is the same single alpha character as typed in Step 3.)
8. The reader will respond with four beeps.
Send Start/Stop Sentinels A
Do Not Send Start/Stop Sentinels B
SELETION CODE: H2
Do Not Send Start/Stop Sentinels B
Send Start/Stop Sentinels A
Track 2 Send Account Number Only A
Track 2 Not Limited to Account Number B
SELECTION CODE: H3
Track 2 Not Limited to Account Number B
Track 2 Send Account Number Only A
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Relacionado con productos y manuales para Lectores De Tarjetas Magnéticas ID TECH Omni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 2.873 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales