ID TECH Omni Manual de usuario Pagina 22
- Pagina / 64
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18
Interleaved 2 of 5 Settings:
Enable/Disable Interleaved 2 of 5
If enabled, Interleaved 2 of 5 symbology will be read, subject to the read-
ing restrictions specifi ed by this set of options. If disabled, the data from the
symbology will be disregarded.
SELECTION CODE: F2
Interleaved 2 of 5 Enable A
Interleaved 2 of 5 Disable B
Fixed Length
Interleaved 2 of 5 symbols are commonly printed in a fi xed format contain-
ing a fi xed number of characters. If this option is ON, the fi rst Interleaved 2
of 5 symbol scanned after power up will set the length of any other symbols
scanned afterwards. If the succeeding scans do not match the length of the
fi rst scan, the scan is rejected by the reader. Power must be reset before an
Interleaved 2 of 5 symbol of a different length will be accepted.
SELECTION CODE: F2
Turn On Fixed Length C
Turn Off Fixed Length D
Check Digit
When Check Digit is selected, the reader takes the last character in the de-
coded data stream as a check digit. It then calculates the correct check digit
for the remaining data and compares it to the last data character. If it is the
same, the data is accepted. If not, the data is rejected. With the Calculate and
Send Check Digit option, the reader will send the check digit as part of the
data stream. If the Calculate but Do Not Send Check Digit option is selected,
the reader will strip it from the data stream before transmission. If the Check
Digit is not calculated, the reader will assume the last data character read
from the symbol is part of the data stream and will not make a comparison
test.
SELECTION CODE: F2
Do Not Calculate Check Digit but Send Whole Data Stream E
Calculate and Send Check Digit F
Calculate but Do Not Send Check Digit G
SELECTION CODE: F2
Interleaved 2 of 5 Enable A
Interleaved 2 of 5 Disable B
Interleaved 2 of 5 Enable A
Interleaved 2 of 5 Disable B
SELECTION CODE: F2
Turn On Fixed Length C
Turn Off Fixed Length D
Turn On Fixed Length C
Turn Off Fixed Length D
Do Not Calculate Check Digit but Send Whole Data Stream E
Calculate and Send Check Digit F
Calculate but Do Not Send Check Digit G
SELECTION CODE: F2
Do Not Calculate Check Digit but Send Whole Data Stream E
Calculate and Send Check Digit F
Calculate but Do Not Send Check Digit G
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Relacionado con productos y manuales para Lectores De Tarjetas Magnéticas ID TECH Omni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 1.659 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales